WAIT - Read the Required Files section before downloading this file.

Required Downloads

Unless stated otherwise, the file listed below must be installed BEFORE the DSC-RX0 Camera Firmware Update in order for it to work properly. If more than one Required file is listed, install them in the order presented on this page.

This utility is required only with Mac OS X® 10.13.

Applicable Models

IMPORTANT: This file is only for use with the models identified. Not all models are sold in all countries.

This information is for the following models:

  • DSC-RX0

About this download

Benefits and improvements

This update (version 2.00) provides the following benefits:

  • Supports Camera Control Box (model CCB-WD1) for wired multi-view shooting
  • Improves wireless multi-view shooting with the PlayMemories™ Mobile application
    Notes:
    • PlayMemories Mobile application version 6.2 or higher is required.
    • Depending on the specifications of the access point, smartphone, tablet, and the radio wave environment of the installation location, the number of devices that can be connected will change. Based on testing, up to 50 units have been connected.
    • Use only on Wi-Fi connections with security measures.

System Requirements

Operating Systems

  • Mac OS® X

File Info

File Name

  • Update_DSCRX0V200.dmg

File Version

  • 2.00

File Size

  • 150.87 MB

Release Date

  • 01-30-2018

Before You Start


Determine if you need this update

This update only applies to DSC-RX0 cameras that currently have a firmware version Ver.1.00.

Check the version of your camera firmware:

  1. Turn on the camera.
  2. Press the Menu button.
  3. At the Menu screen, select Setup, and then select Version.
    Menu Version Screen
  4. The firmware version is displayed on the camera screen.
    Firmware Version Screen
    Note: If the current firmware version is Ver.2.00, this firmware update is installed on your camera.

Before You Start

  • WARNING! This firmware update and any changes incurred by it are permanent. It's not possible to return to a previous firmware version after updating this firmware. By continuing this update process, downloading and updating this firmware, you acknowledge that you are aware and understand that this update cannot be reversed.
  • IMPORTANT: Don't allow the computer to enter Sleep (Standby) mode during the update process. To change these settings, refer to your computer manual or consult the manufacturer.
  • This update process requires the following items for proper updating:
    • A computer with:
      • Available Hard Disk Space: 600 MB or more
      • Installed Memory (RAM): 512 MB or more
      • Apple® Mac OSX® versions 10.10 - 10.13
        IMPORTANT: For computers running Mac OS X version 10.13, the DriverLoader_1013 software must be installed before installing the camera software update for each camera that's being updated.
    • Camera power supply:
      • This update can only be performed when the remaining battery level has three bars Battery Indicater or more.We recommend using a fully charged battery pack.
        WARNING! The camera may not operate properly if the power is interrupted during the update.
    • USB cable:
      • Use only the USB cable supplied with the camera.
        IMPORTANT: Update functionality isn't guaranteed with any other USB cable.
  • Remove the memory card from the camera
  • Make sure all other devices are disconnected from the camera
  • Save all work and close all other programs.

Download & Install


Download and Update the Firmware

  1. Download the Update_DSCRX0V200.dmg file to a temporary or download directory (please note this directory for reference).
  2. Go to the directory where the file was downloaded and double-click the Update_DSCRX0V200.dmg file. The file is expanded.
    Note: Do not connect the camera to the computer yet.
  3. On the desktop, double-click the SystemSoftwareUpdater icon.
    System Software Updater icon
  4. At the prompt, enter the Username and Password for the administrative account, and then click OK.
    System Software Updater Password
  5. The System Software Updater starts.
    Connect the Camera and Computer Screen
  6. Turn on the camera.
  7. Verify that Mass Storage is selected in the USB Connection setting of the camera:
    1. On the camera, press the Menu button.
    2. At the Menu screen, select Setup, then select USB Connection, and then make sure that Mass Storage is selected.
      Mass Storage USB Setting
  8. Ensure the memory card is removed from the camera.
  9. Connect the camera to your computer using the supplied USB cable. USB Mode will appear on the camera screen.
    Notes:
    • If the message Could not find the camera for this update appears on the computer display, disconnect and reconnect the USB cable, or try another USB port on the computer.
    • Sometimes when the camera is connected to the computer with the USB cable, a message appears to restart the computer. If this occurs, briefly remove the battery and disconnect the AC adaptor (if connected), restart the computer, and then start the firmware update procedure again.
  10. At the System Software Updater screen, click Next.
    Connect the Camera and Computer Screen
  11. Check the current version displayed.
    Current Version Screen
    Note: If the current version is Ver.2.00 or higher, your camera doesn't need this update. Stop the USB connection, and click Finish. Then disconnect the USB cable and power off the camera. Briefly remove the battery and disconnect the AC adaptor (if connected), and then power on the camera again.
  12. If the current version is Ver.1.00, click Next.
  13. The camera will now automatically reset.
    Reset Camera Screen
  14. After the camera is reset, the update starts. The progress bar appears while updating (approximately 15 minutes).
    Updating Screen
    WARNING! Do not power off the camera or disconnect the USB cable until the update process is complete.
    Note: Depending on the OS version you're using, a loading icon may appear.
  15. When the update process completes, the camera automatically restarts (which may take a few minutes).
    Note: Wait for the camera to power on and return to the previous screen.
  16. When the camera finishes restarting, and the screen reappears, click Finish.
    Update Finish Screen
    Note: The message Recovering data Please wait... can rarely display on the camera, this is normal. Wait for this message to go away before disconnecting the USB cable.
    Recovering data Please wait... message
  17. When the update is finished, disconnect the USB cable.
  18. Check the current firmware version to confirm that the update has successfully installed.
    • If the version is Ver.2.00, the firmware update was successful.
    • If the version isn't Ver.2.00, download and install the update again.